Additel PCal User Manual User Manual

Additel/PCal User Manual Additel Corporation www.additel.com

- 9 - UUT Flow chart: Below shows a flow chart of the UUT setup wizard. New UUT: In UUT Management menu, users can create a new UUT. The below step

- 10 - Third: Choose the Manufacturer Fourth: Choose the Customer

- 11 - Fifth: Choose the Application Site

- 12 - UUT Management: The UUT Management allows user creating, editing, exporting and deleting the data associated with all gauges in the UU

- 13 - When creating a new reference, the Model, Certificate No., Reference No. and Accuracy are required. Schedule: In this section, y

- 14 - Maintenance The Maintenance menu allows user to manage all the entered or acquired information stored in database. For management

- 15 - When selecting the accuracy, you can select a custom accuracy which the steps are outlined below. If the pressure range is (0 to 10

- 16 - Profiles: The profile editor provides access to all test profiles stored in the database. The profile detail box is used to crea

- 17 - Manufacturers: The manufacturers editor allows access to the information about each manufacturer stored in the database. Only

- 18 - Application Site: The application sites editor allows access to the information about each application site stored in the database

- 1 - Contents Introduction ...

- 19 - New UUT Wizard: Create a new UUT. Calibration Wizard: Create a new calibration. Certificate: Refer to the Certificates section. Documents:

- 20 - Second: The software will attempt to auto detect the calibration reference. If the reference is a non-supported gauge then the information ca

- 21 -

- 22 - Account: If the reference is a supported item it may also be edited. Third: Choosing the UUT. Fourth: Calibration Profile Account: You can ch

- 23 - If you want to create a new profile, please see Maintenance section. Fifth: Enter the environmental conditions Sixth: Exercise Calibration S

- 24 - There are two methods that can be selected while calibrating a gauge. Reverse Calibration means to match the UUT reading to the t

- 25 - When performing pressure switch calibrations, a pressure switch is required. You can validate the accuracy of pressure switch by the P/F fro

- 26 - Certificates Build Certificate In this section, you can build certificate. First: General Information Second: Choose the reference.

- 27 - Third: enter the environmental conditions.

- 28 - Certificate Management Certificates are the documents that record the calibration of gauges. The certificate templates of PCal are

- 2 - Introduction Overview Thank you for purchasing Additel/PCal from Additel Corporation which is one of the leading providers of process calibrat

- 29 - Schedule: In this section, you can manage the gauges by schedule date. Use the search button to view a list of Gauges. “Due Date” means the d

- 30 - Certificate Template PCAL allows for the ability to create customer certificates using excel. These certificates can be fully customize

- 31 - Now you can edit or reset the template by selecting the appropriate links Please refer to the following steps: 1. Clicking the Edit Templ

- 32 - Appendix PCal Pressure Units PCal uses the following standard units and associated conversion factors from kPa. All conversion fa

- 33 - # UUT_DueDate# UUT Due Date # UUT_Status# UUT Status # UUT_CreateDate# UUT Created Date # UUT_UpdateDate# UUT Updated Date Model #Model# Mo

- 34 - #Reference{0}CalibrationDate# Reference{0} Calibration Date #Reference{0}Due# Reference{0} Due Date #Reference{0}Status# Reference{0} Status #

- 3 - Installation System Requirements Hardware Requirements Computer: CPU-Intel Pentium II (or better) Memory: 1GB (minimum) Hard Disk fre

- 4 - When the installation is completed, the following icon will be appeared on the desktop.

- 5 - Starting PCal License Key The first time you run PCal after installation, a Product Activation interface will be shown as below. The license

- 6 - After the initial installation, PCal will prompt you for your username and password. Initially, you can enter Administrator’s

- 7 - Basic Settings Basic settings can be edited anytime. For a better experience we recommend you modify after your initial setup as it

- 8 - Default: choose Date and Time Format, restore defaults, and change the location of exported documents. The “Auto open excel document” c